Paxton

Cardlock 1 extra user card amber 875-001AThis is one additional user card in amber for a Paxton CARDLOCK system. Paxton lists it for use with the Switch2 or Compact system, so you can add another user to an existing installation without replacing the cards already in use.Please check that your system is a CARDLOCK Switch2 or Compact before ordering.Key featuresOne extra user cardAmber colourFor Paxton CARDLOCK Switch2 or Compact systemsPaxton sales code 875-001A..

Cardlock 1 extra user card green 875-001GThis is one additional user card in green for a Paxton CARDLOCK system. Paxton lists it for use with the Switch2 or Compact system, so you can add another user to an existing installation without replacing the cards already in use.Please check that your system is a CARDLOCK Switch2 or Compact before ordering.Key featuresOne extra user cardGreen colourFor Paxton CARDLOCK Switch2 or Compact systemsPaxton sales code 875-001G..

Cardlock 1 extra user card red 875-001RThis is one additional user card in red for a Paxton CARDLOCK system. Paxton lists it for use with the Switch2 or Compact system, so you can add another user to an existing installation without replacing the cards already in use.Please check that your system is a CARDLOCK Switch2 or Compact before ordering.Key featuresOne extra user cardRed colourFor Paxton CARDLOCK Switch2 or Compact systemsPaxton sales code 875-001R..

The Paxton E50 exit button, sales code 356-310, releases the door from the inside on Compact, Switch2, Net2 or Paxton10 systems. It is part of Paxton's E series, styled to match Paxton's proximity readers and keypads.Green LED lit continuously. On Switch2 and Net2 it flashes when pressed to show the door has been released. On Compact it stays lit but does not flash.Operating voltage 10V to 14V DC, current consumption 70mA.5m cable fitted. Extendable up to 25m in Belden 9538 or up to 100m in Belden 9540.Interior use only. Not moisture resistant. Not hands-free compatible...

Paxton Easyprox Battery Pack – 4 x AA High Capacity (746-003) Ensure uninterrupted operation of your Paxton Easyprox access control systems with the Paxton Easyprox Battery Pack (746-003). This high-capacity battery pack is specifically designed for use with Paxton's Easyprox Compact, Easyprox Compact Keypad, and Easyprox Nano units, providing reliable power for sites with high traffic or frequent access events. Key Features: Compatibility: Suitable for all Paxton Easyprox products in the range, including Compact, Compact Keypad, and Nano models. High-Capacity Performance: Ideal for busy access points or locations with a high number of users. It ensures a consistent and long-lasting supply or power to the reader. Easy Installation: Simply remove the unit from the door, access the battery compartment, replace the battery pack, and refit the access plate. Total install time is under 5 minutes. Seamless Operation: Post-installation, the unit continues to function as usual without any additional configuration. Product Details: Sales Code: 746-003 Battery Type: 4 x AA high-capacity batteries Recommended Use: Particularly suited for Easyprox Nano units and environments with heavy usage Maintain the efficiency and reliability of your access control systems with this essential battery pack, ensuring security is never compromised due to power issues...

Paxton Net2 proximity ISO cards, sales code 692-052, supplied as a pack of 500. These are user tokens for a Net2 access control system. They have no magnetic stripe and no signature strip.125kHz carrier frequency.Plastic card measuring 86mm x 55mm x 0.85mm.Can be printed on using a universal card printer.Hitag2 technology with proprietary encoding, including an authentication protocol based on a password exchange between token and reader.Issued by entering the user in the Net2 PC software, then presenting the token to the desktop reader.Paxton lists the Net2 desktop reader, USB (514-326) to complete the system...

A 1A 12V DC power supply in a plastic enclosure, Paxton part number 998-241. It belongs to the range of 12V DC supplies Paxton makes for use with its own access control systems.Mains input of 100 to 240V AC (1.2A).Operating voltage of 11.9V to 12.1V DC.Designed to connect to a standard UK mains supply via a switched fused spur.ABS plastic housing. A fitting kit is included.No tamper switch.Not moisture resistant. If used outside, it must be protected in a weatherproof housing...

The Paxton 12V 2A DC power supply in a plastic cabinet, sales code 857-250, is a boxed backup power supply for Paxton access control. With a suitable battery fitted it keeps supplying 12V DC during a mains failure. How long depends on the system's load and the battery's capacity.Input 100 to 240V AC (1.2A), 50 to 60Hz. Output 12V DC, 2A. Three 12V DC outputs.Switch-mode, double-insulated PSU with a 1A battery charging current.Cabinet holds the PSU plus a Net2 or I/O controller, with room for an optional 12V 7Ah backup battery.Tamper switch raises an alarm if the lid is opened when connected to a controller or I/O board. Mains failure warning included.Operating temperature 0°C to +45°C. If used outside it must sit in a weatherproof housing.Designed to connect to a standard UK mains supply via a switched fused spur...

The Paxton 2A/12V DC power supply with no housing, sales code 857-090, is the unboxed version of Paxton's 857-250 boxed backup power supply. Paxton supplies its 12V DC power supplies for use with its own access control systems.Runs from 100 to 240V AC mains.12V DC output at 2A.Designed to connect to a standard UK mains supply via a switched fused spur.Installation instructions are supplied with the unit.The boxed version, which takes a backup battery, is the 12V 2A DC power supply in a plastic cabinet (857-250)...

The Paxton Entry VR panel, part number 337-510, is the vandal resistant external panel of the Entry door entry system, in the surface mount version with a rain hood. The hood adds a 41mm mantel to protect the screen and keypad from rain.Marine grade stainless steel with an IK10 impact rating. IPX5 moisture resistance.Full colour pan/tilt camera with two way audio.Built-in keypad and RFID reader. Reads Paxton, EM and MIFARE (UID only) tokens.Powered over Ethernet, IEEE 802.3af class 0.Operating temperature of -20°C to +50°C.Works with Net2, Standalone and Paxton10. Each panel is associated with an Entry control unit, which is the interface to the door hardware...

Paxton Exit Button – E75 - 376-310Enhance your access control system with the Paxton Exit Button – E75, a robust and stylish solution designed for seamless integration with Paxton's Compact, Switch2, Net2, and Paxton10 systems. Part of the E series, the E75 exit button complements Paxton's range of proximity readers and keypads, ensuring a cohesive and professional appearance across your security installations.Key Features: System Compatibility: Fully compatible with Paxton's Compact, Switch2, Net2, and Paxton10 systems, offering versatile application across various access control setups. Aesthetic Design: Supplied with a black fascia as standard, with optional white/grey replacement fascias available free of charge to Paxton registered installers, allowing for customisation to match interior designs. LED Indicators: Features a green LED that remains lit continuously. When used with Switch2 and Net2 systems, the LED flashes upon button press to indicate door unlocking. With Compact systems, the LED remains steadily illuminated. Ease of Installation: Designed to fit standard UK recessed backboxes, facilitating straightforward installation in a variety of settings. Interior Use: Suitable for indoor environments, providing reliable performance in protected areas. Technical Specifications: Operating Voltage: 10V – 14V DC Current Consumption: 70mA Operating Temperature: -20°C to +55°C (-4°F to +131°F) Cable Length: Up to 5m (16ft) Dimensions: 86mm (W) x 94mm (H) x 16mm (D) Environment: Indoor use only The E75 exit button's durable construction and compatibility with multiple Paxton systems make it an ideal choice for enhancing the functionality and aesthetics of your access control installations...

The Paxton Entry control unit, part number 337-727, is the central interface between an Entry door entry panel and the door. It also provides data and PoE to the Entry monitors.Built-in 4 port PoE switch for expanding the system.2A 12V DC power supply.Tamper switch for extra security.Battery backup capability. The battery is not supplied.Plastic cabinet housing.Components interconnect with Cat5 or standard RJ45 terminated patch cables. PoE runs power and data along the same cable, so separate power supplies are not needed.When connected to Net2, access to the building can be gained with a PIN, code or proximity token...

Plugs into the existing LAN/WAN and can be used Power over Ethernet (PoE) Wireless bridge from Net2 to wireless control units Multiple Net2Air Bridges can be placed around a site Gives more flexibility on installing wireless control units..

Paxton Net2 Magstripe cards - 695-573 - pack of 10These Paxton Net2 cards are magnetic stripe only cards, sold in packs of 10 under Paxton code 695-573. They contain no proximity element, so they are used with swipe readers and will not work on Net2 proximity readers.The cards are the standard 86mm by 55mm size. If your site uses proximity readers, choose a Paxton Net2 proximity card instead.Key featuresMagnetic stripe only, with no proximity elementFor swipe readersNot compatible with Net2 proximity readersPack of 10 cardsSpecificationsManufacturer code: 695-573Card size: 86mm x 55mmPack size: 10..

Paxton Net2 Plus 1 Door Controller (682-493)The Paxton Net2 Plus 682-493 is the single-door Net2 controller supplied as a bare circuit board, with no housing or power supply. It’s the version installers choose when fitting a controller into an existing cabinet with its own DC supply, and when replacing an old Net2 Classic controller. That second job became more urgent in 2026, when Paxton released Net2 v7. A system with even one Net2 Classic in its database can’t upgrade beyond v6.9, which locks it out of v7 and the multi-factor authentication it adds to software login.Part number: 682-493Format: Net2 Plus PCB only, 126 x 116 x 25 mmDoors: 1 per controllerPower: 12V to 24V DC (±20%), 200mA; power supply not includedNetwork: On-board TCP/IP (100Mbit/s, auto MDIX) and RS485Reader ports: 2, taking up to 4 readers or keypads in totalUsers: Up to 50,000 users and tokensWarranty: 5 yearsEach Net2 Plus controller makes its own access decisions. If the network or PC goes down, it keeps letting the right people through and stores the events, then reports them back to the software once communications return. It also holds its data for up to 30 days through a total power loss.The on-board TCP/IP connects the controller straight to your LAN. The same controller can also act as the network interface for a wired RS485 daisy chain of other Net2 Plus controllers, so a run of doors needs fewer network points and no separate TCP/IP to RS485 converter.The board has inputs for an exit button and a door contact, plus separate inputs to monitor your power supply and tamper switch. A volt-free relay rated at 4A, 24V DC drives the lock, and there’s an alarm/bell output and a dedicated intruder alarm input.Both reader ports work with Paxton readers and keypads. Compatible third-party readers can connect over 26-bit or custom Wiegand.During installation, give the controller a fixed IP address and configure it through the Net2 Configuration Utility. The board isn’t moisture resistant, so it needs to sit indoors or inside a weatherproof housing.The controller runs on Paxton’s Net2 software, which manages sites of up to 1,000 doors and 50,000 users. Net2 Lite is free and suits most sites. Net2 Pro adds features including Net2Online, a browser-based interface for managing users, running lockdown and viewing reports from any device...

Paxton Net2 Plus 1 Door Controller, PoE+, Metal Cabinet (682-721)The Paxton Net2 Plus 682-721 is a single-door Net2 controller in a metal cabinet, powered entirely by Power over Ethernet. There’s no mains supply to wire in, because a single CAT5 cable from a PoE switch or injector carries both data and power. How much power you get depends on the switch. On a PoE+ (802.3at Type 2) port, the cabinet’s power supply delivers up to 1.5A at 12V DC for the controller, readers and lock. On a standard PoE (802.3af) port, that drops to 0.8A, so add up the draw of your lock and readers before choosing where to plug it in.Part number: 682-721Cabinet: Powder-coated metalPower input: PoE, 36V to 57V DC over CAT512V DC output: Up to 1.5A on PoE+ (Type 2), 0.8A on standard PoE (Type 1)Network: On-board TCP/IP and RS485Reader ports: 2, taking up to 4 readers or keypads in totalUsers: Up to 50,000 users and tokensOperating temperature: 0°C to +45°CWarranty: 5 yearsBecause the power arrives over the network, there’s no battery backup inside the cabinet. Paxton recommends running the PoE switch or injector from a UPS, so the door keeps working through a mains cut.Each Net2 Plus controller makes its own access decisions. If the network or PC goes down, it keeps permitting or denying access as normal, then reports the activity back to the software once communications return. Any change you make in the software is sent to the controller and stored there straight away.The built-in TCP/IP converter connects the controller to your LAN, and it can also run a wired RS485 daisy chain of other Net2 Plus controllers. That cuts the number of network points a run of doors needs. Flash memory lets you update the controller’s firmware without swapping hardware.The volt-free relay can switch any lock or electrical device within its 4A, 24V DC rating. Exit buttons, door contacts, tamper switches and alarm devices all connect directly to the board. You can switch end-of-line resistors into the circuit when you need them, so external terminating resistors aren’t required.A colour-coded label shows where the reader and power connections go, and diagnostic LEDs sit next to their terminals. Give the controller a fixed IP address and configure it through the Net2 Configuration Utility. Mount the cabinet indoors on the secure side of the door, so the controller that drives the lock is out of reach. If it has to go outside, put it in a weatherproof housing.Both reader ports work with Paxton readers and keypads, as well as compatible third-party readers. The controller runs on Paxton’s Net2 software, which manages up to 1,000 doors and 50,000 users. Net2 Lite is free and suits most sites. Net2 Pro adds features including Net2Online, which lets you manage users, run lockdown and view reports from a web browser.If you’re replacing an old Net2 Classic controller, the 682-721 is a direct way to do it over your existing network. Since Net2 v7 launched in 2026, any system with a Classic controlle..

Paxton Net2 Plus 1 Door Controller, 12V 2A PSU, Plastic Cabinet (682-531)The Paxton Net2 Plus 682-531 is a single-door Net2 controller supplied ready-mounted in a plastic cabinet with its own mains-powered 12V 2A power supply. It’s the straightforward choice when there’s a mains spur near the door and no PoE switch to power the controller from. Everything at the door shares that 2A: the controller, its readers and the lock. The total load must not exceed the 2A rating, so add up the draw of your lock and readers before you commit to the layout. Part number: 682-531 Cabinet: Plastic, for indoor installation Power supply: 12V DC, 2A, mains input 100–240V AC Battery backup: Space for a 12V 7Ah battery (sold separately) Network: On-board TCP/IP and RS485 Reader ports: 2, taking up to 4 readers or keypads in total Users: Up to 50,000 users and tokens Warranty: 5 years The power supply connects to a standard UK mains supply through a switched fused spur. Paxton recommends fitting a backup battery, and the cabinet has room for a 12V 7Ah unit. If the mains fails, the supply switches to battery automatically and keeps the door running for a period that depends on your system’s power draw and the battery’s capacity. A deep discharge cut-off disconnects the battery if it falls below 9.5V, and LEDs on the supply show whether it’s running from mains or battery.The power supply also has a mains failure alarm output, and the controller has a dedicated PSU fail input to match. Alongside it are inputs for an exit button, door contact and tamper switch, plus an intruder alarm input and an alarm/bell output. The volt-free relay can switch any lock or electrical device within its 4A, 24V DC rating, and end-of-line resistors switch in on the board when needed.Net2 Plus controllers make their own access decisions. If the network or PC goes offline, the door keeps working as normal and the activity is reported back once communications return. Changes made in the software are sent to the controller and stored there straight away.A built-in TCP/IP converter connects the controller to your LAN through a standard RJ45 plug, and the RS485 connection lets it act as the network interface for a daisy chain of other Net2 Plus controllers. Give it a fixed IP address and configure it through the Net2 Configuration Utility. A colour-coded label and diagnostic LEDs beside the terminals make wiring easy to check. The controller works with Paxton readers and keypads, along with compatible third-party readers, and runs on Net2 software. Net2 Lite is free and suits most sites. Net2 Pro adds features such as the Net2Online browser interface...

A Net2 Plus single door controller in a metal cabinet with a 12V 2A power supply, Paxton part number 682-813. Its built-in TCP/IP converter lets it plug straight into a TCP/IP network with an RJ45 plug.Use Paxton readers or compatible third-party readers on its two reader ports.Up to 50,000 users or tokens, with 4 to 8 digit PIN and code lengths.Door open time adjustable from 1 second to 5000 seconds.Inputs for PSU fail and tamper, plus a dedicated intruder alarm.Diagnostic LEDs sit close to their terminals. A colour coded label shows the reader and power connections.FLASH memory allows upgrades. Different control units can be mixed on a site...

Paxton Net2 Pro Software OverviewNet2 Pro (930-010) is the paid upgrade to Paxton’s Net2 access control software. It includes everything in the free Net2 Lite and adds Paxton’s advanced features. Paxton’s Net2 Lite is an excellent choice for most sites. However, the Pro version adds time and attendance, fire alarm and multi-zone intruder alarm integration, lockdown and remote management directly into your system. It’s a one-off licence, installed on a Windows PC.Paxton part code: 930-010Licence: one-off, supplied as a card with a download link and unique licence keyCapacity: up to 50,000 users and 1,000 doorsRuns on: Windows PCSystem: Paxton Net2What Net2 Pro AddsWith Timesheet and Timeline, staff clock in and out on the same proximity readers that open the doors. The hours can then be exported to HR applications. Card designer prints user photos and company details straight onto access cards. If more than one business shares a building, landlord-tenant permissions restrict each operator to managing tokens within their own area.Security lockdown secures the site in an emergency and lets chosen security staff move freely. Anti-passback stops someone passing their token back to a second person to get into the same area, such as a car park. Pro also adds fire alarm integration and multi-zone intruder alarm integration.Remote Management with Net2Online and Paxton ConnectRemote site management needs Net2 Pro. Net2Online gives you a browser interface, so you can add users, open doors, run roll call reports and trigger lockdown from any device. The Paxton Connect app does the same from a smartphone or tablet. Net2Online needs Pro v6.01 or above, and Paxton Connect needs v6.00 or above. Neither one stores your data in the cloud, because both only relay information between the system and the device, so your data remains protected.Check Your Controllers Before Moving to Net2 v7Paxton released Net2 v7 in February 2026, and it brings new security features including multi-factor authentication. It won’t install on any system that still has a Net2 Classic door controller in its database, and those sites stay on v6.9. Classic controllers haven’t been sold in the UK since 2014. Replacing them with Net2 Plus controllers, such as the Paxton Net2 Plus 1 Door Controller (682-493), opens up v7. With Net2 Plus controllers in place, a Pro licence gives you access to every feature in the latest Net2 software...

Paxton Net2 proximity clamshell cards, sales code 693-112, supplied as a pack of 10. They are user tokens for a Net2 access control system.125kHz carrier frequency.ABS/plastic clamshell construction, 86mm x 55mm x 2mm.Hitag2 technology with proprietary encoding, including an authentication protocol based on a password exchange between token and reader.Issued by entering the user in the Net2 PC software, then presenting the token to the desktop reader.Once programmed, presenting the card to a reader looks up the user's access permissions and grants or denies entry.Paxton lists the Net2 desktop reader, USB (514-326) to complete the system. Paxton10 compatible: Paxton10 readers also read Paxton proximity tokens, so these can be used on a Paxton10 system as well as Net2...

Paxton Net2 proximity ISO cards, sales code 692-448, supplied as a pack of 10. These are user tokens for a Net2 access control system. They carry a magnetic stripe and a signature strip.125kHz carrier frequency.Plastic card measuring 86mm x 55mm x 0.85mm.Can be printed on using a universal card printer.Hitag2 technology with proprietary encoding, including an authentication protocol based on a password exchange between token and reader.Issued by entering the user in the Net2 PC software, then presenting the token to the desktop reader.Paxton lists the Net2 desktop reader, proximity and magstripe (350-910) to complete the system. Paxton10 compatible: Paxton10 readers also read Paxton proximity tokens, so these can be used on a Paxton10 system as well as Net2...

Paxton Net2 Proximity ISO Cards Without Magstripe Overview These genuine Paxton 692-500 Net2 proximity ISO cards are the standard access control card for Paxton Net2 systems, supplied in a pack of 10 for teams that need to issue, replace or expand credentials with minimum fuss. Each card arrives blank and ready to print, making them equally useful as plain access control cards or as branded staff ID. What you get in the pack Each 692-500 card is manufactured to ISO standard CR80 dimensions (86mm × 55mm), so it sits in any standard card holder and feeds through any ID card printer. There is no magnetic stripe and no signature panel on the rear face, which leaves the full surface free for printing. The pack contains 10 individually encoded cards, each carrying a unique number that the Net2 system uses to identify the user. How the cards work with Net2 Issuing a card is a two-step process that any Net2 installer will find straightforward. Enter the user's details using the PC software, then present the card to the desktop reader; the unique number is read into Net2 and the card is ready for use. Once issued, a user simply presents the card to any enrolled Net2 reader, and access permissions are instantly looked up. Access is then granted or denied as appropriate. Security technology Paxton tokens use Hitag2 technology with proprietary encoding. This includes an authentication protocol in the form of a password exchange between the token and the reader, adding a layer of security beyond basic proximity. The 125kHz carrier frequency is the standard across the Net2 access control range, so 692-500 cards are compatible with all Net2 proximity readers. Printing and customisation The blank white PVC card takes print from any compatible ID card printer, which means you can add a photo, job title, logo or building zone directly to the card face. So, this is a great option for sites that want cards to double as staff photo ID. Offices, schools, healthcare premises and membership organisations find this more practical than key fobs, because they double as ID and access control. If you need a card with a magnetic stripe for a system that also reads swipe cards, the Paxton Net2 proximity ISO card 692-448 carries both a proximity chip and a hi-co magstripe in the same CR80 format. For staff or visitors who prefer something they can attach to a keyring rather than carry in a wallet, the Paxton Net2 Proximity Key Fobs 695-644 (pack of 10) use the same Net2 proximity technology and enrol in exactly the same way. The 692-500 pack of 10 is the right choice when you are running a Paxton Net2 access control system and want genuine, printable cards that enrol cleanly, carry proper Hitag2 security, and leave no compatibility guesswork. Specification Detail Part number692-500 Compatible systemPaxton Net2 Carrier frequency125kHz TechnologyHitag2 with proprietary encoding Card formatISO ..

Paxton Net2 proximity ISO cards, sales code 692-053, supplied as a pack of 500. These are user tokens for a Net2 access control system. They carry a magnetic stripe and a signature strip.125kHz carrier frequency.Plastic card measuring 86mm x 55mm x 0.85mm.Can be printed on using a universal card printer.Hitag2 technology with proprietary encoding, including an authentication protocol based on a password exchange between token and reader.Issued by entering the user in the Net2 PC software, then presenting the token to the desktop reader.Paxton lists the Net2 desktop reader, proximity and magstripe (350-910) to complete the system. Paxton10 compatible: Paxton10 readers also read Paxton proximity tokens, so these can be used on a Paxton10 system as well as Net2...

Paxton Net2 proximity self-adhesive discs, sales code 660-100, supplied as a pack of 10. Each disc is a Net2 user token that sticks onto something the user already carries, such as an ID card.For use with the Net2 system.Paxton suggests fixing it to an ID card, wallet, smart device or keyring.Hitag2 technology with proprietary encoding, including an authentication protocol based on a password exchange between token and reader.Issued by entering the user in the Net2 PC software, then presenting the token to the desktop reader.Paxton lists the Net2 desktop reader, USB (514-326) to complete the system. Paxton10 compatible: Paxton10 readers also read Paxton proximity tokens, so these can be used on a Paxton10 system as well as Net2...